> For the complete documentation index, see [llms.txt](https://teamhelp.sipgate.co.uk/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://teamhelp.sipgate.co.uk/use-sipgate/troubleshooting-problem-solving/how-can-i-solve-problems-with-the-router.md).

# How can I solve problems with the router?

Troubleshooting router problems affecting VoIP calls, including NAT configuration, STUN server setup, and port forwarding guidance.

The errors listed below can usually be rectified by simply adjusting the configuration in the router:

The call can only be heard in one direction.\
Your VoIP end device does not register or loses its registration after a while.\
The called party continues to ring even though you have already hung up.\
You cannot be reached from outside.\
You can dial a number but do not hear any ringing.\
The call acceptance is not transmitted to the caller.\
The call is disconnected after a while.

#### What does a NAT router actually do?

A router is used when there is only one Internet access, but this is to be made available for several devices or computers in the local network.

The NAT router thus serves as a distributor for Internet access which independently establishes the Internet connection to your Internet provider. It receives a globally unique IP address (according to the scheme 123.123.123.123) from the Internet provider so that it can also send requested data to the router individually. The router in turn makes the Internet connection available to all devices connected to it in the local network (LAN).

To ensure that each VoIP end device that you have connected to the router can also be addressed individually, each of these end devices automatically receives an internal IP address from the router.

#### Which data is being transmitted?

Your router must know that sipgate will send and receive both voice data and data for establishing a connection. These two types of information always come to your router via the same route:

Voice data is transmitted via UDP over the so-called RTP port.\
Switching data is transmitted via UDP via the SIP port.

Both the RTP port and the SIP port can usually be defined in the end device settings.\
Please refer to the supplied manufacturer's manual for more information on where exactly you can set the SIP or RTP port.

#### Where do I enter the necessary data?

The router needs to know to which device this data must be sent. To do this, you need to know the local IP address of your VoIP end device (e.g. 192.168.1.12).

Some devices have a display on which the IP address can be shown (further information on the status of the IP address can be found in the manufacturer's manual).\
Softphones (e.g. Phonerlite) always use the IP address of the computer on which they are used.\
Your router can also be helpful: In the router's configuration screen, you will often receive a corresponding list of currently assigned local IP addresses via a status page.

Once you have determined the IP address, make a note of it for the next step.

#### Change to TCP, TLS, and IPV6

In some cases, it may be helpful to switch the phone's SIP communication to TCP or TLS. Switching to IPv6 can also be helpful.

#### Example Configuration for VoIP-Devices

Please do not use a STUN server with sipgate connections. STUN can cause problems with many router models, e.g. one-way audio or failed registrations. Please delete any STUN entry in your VoIP devices. You can find out where you can deactivate the STUN server in your telephone in our configuration help.

If you use several VoIP end devices in a network, you will find various instructions on how to set them up individually in our configuration help.

#### What is STUN?

The STUN Protocol, or Session Traversal Utilities for NAT, can assist devices behind a NAT firewall or router with routing UDP packets. sipgate connections generally work reliably without a STUN server; for sipgate endpoints, STUN should remain disabled.

#### My Problems still exist

Check the current software (firmware) of the router. Most router manufacturers constantly update the firmware of their devices. You can usually download these free of charge from the manufacturer's website.

You will find instructions for updating the firmware in the manufacturer's manual. If necessary, the port sharing must be set up again after updating the firmware. Alternatively, check the FAQ instructions on the manufacturer's website or contact the manufacturer's support team.
